2024 hottest OLED Display Module

For Arduino UNO R3 STM, 4 I2C OLED 0.96-inch OLED Display Modules IIC SSD1306 128-64 LCD White with Du-pont Wire 40-Pin Female to Female

Price: $15.99

updated version: Instead of the VCC pin on the first row, use the GND pin instead; it has already been soldered. 40 DuPont lines are free, and the quality is affordable. IIC Serial OLED Blue LCD Display Display Unit: Interface: SCL: Serial Clock; SDA: Serial Data; VCC: 3.3-5V; GND: Ground; viewing angle: greater than 160 degrees; Operating range: -30 to 80 degrees Without a backlight, it is an OLED display with minimal power consumption.Only 1.4mm of glass is actually thick. the color white; 128*64 resolution; 27 MM * 27 MM * 4.1 MM volume The IIC address can be altered, making it simple to use with various machines. SSD1306's driver IC Supported platforms include the Arduino, MSP430, 51, STIM32, and 2,...

Teyleten Robot SSD1309 2.42 inch 128x64 OLED LCD Display Module for Arduino UNO R3 - White Light

Price: $13.88

R3, R4, and R5 are used to select the interface, either SPI or IIC. Moving the resistor from R4 to R3 is required for IIC communication, and R5 is soldered with a 0 ohm resistor. By specifying three resistors, you may switch between SPI and I2C communication. R3 R4 R5

IIC Serial 0.96 inch Yellow Blue OLED Display Module for Arduino 128x64 I2C SSD1306 12864 LCD Screen Board GND VCC SCL SDA

Price: $3.47China lcd 240x128 factory

Landon Sung

ALMOCN 2PCS 0.96" I2C IIC Serial 12864 128X64 OLED Display Module with SSD 1306 Driver (2PCS, Blue)

Price: $9.99

This I2C display module has a 0.96-inch diagonal, 128 x 64 resolution, a >160° viewing angle, and a 3.3V to 5V DC support voltage. Power usage: 0.04W while operating normally, 0.08W when the entire screen is lighted. With a high resolution of 128 x 64 pixels, no backlight is required, and self-illumination, the pixels are easily distinguishable even in brighter conditions like direct sunshine. SSD 1306 is the embedded driver IC. I2C/IIC interface for communication, only two I/O ports required Our I2C OLED display module has four square holes, making it simple to install, operate, and work with. It may be used extensively with the Raspberry Pi, the 51 series, the MSP430 series, the STM32/2, and other chips.

Self-Luminous Display Board Compatible with Arduino Raspberry PI ACEIRMC 4pcs 0.96 Inch OLED Module 12864 128x64 SSD1315 Driver White

Price: $12.99

Applications include a 0.96-inch OLED module for displaying text and graphics on microcontroller applications; It is compatible with a wide range of chips, including the Arduino Mega, Raspberry Pi, 51 MCU, STIM 32, etc. 128 x 64 resolution; greater than 160 degree angle of view Support voltage: 3.3V-5V DC; power usage: 0.04W during normal operation, 0.08W when the entire screen is lighted SSD1315 is an embedded driver IC. I2C/IIC Interface, only 2 I/O ports required for communication; It is compatible with the Raspberry Pi, MMDVM, and Pi-Star. Without a backlight, the OLED display performs better in low light than an LCD display, so the clarity of the tiny will appeal to you. The pixels on the screen are sharp, very legible, and vivid, and they even stand out rather nicely.

For instrument display mobile devices, DC 3.3V 1.28'' LCD Display Module, 240x240 Resolution Display Equipment

Price: $14.99

A 1.28 inch 240*240 IPS LCD display screen is what it is.It employs an IPS color display panel, which produces a more vivid display effect than a standard TFT LCD display. SPI communication using 4 pins. Direction of the display is movable. Display with full viewing angles. SHOP CONFIDENTLY: Please feel free to contact us if you have any questions so that we can give you the best service possible.Until you are completely satisfied, we will offer after-sales service.